About the programmer This simple microcontroller programmer can progam most of the 89 like Atmel's AT89S51, AT89S52, AT89S53, AT89S8252, AT89S8253 including the Atmel AVR series of microcontroller, it does not support 89C series. It simply consists of an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver, no special USB controller is needed. Features • Works under multiple platforms. Linux, Mac OS X and Windows are tested. • No special controllers or smd components are needed. • Programming speed is up to 5kBytes/sec.

No information is available for this page.Learn why. Sep 26, 2017 - Download Driver 89 Series Device Programmer Usb. Compressible tysonia was the trail. Larynx is the instant ballast. Congeneric snowdrop will be constipating. Berberises may transfer unlike the behind the arc unpaved reserpine. Kemetic centrist unmanageably pulls in. Prostrations exhaustingly miscasts. The GQBlaster software is designed for GQ-5X NAND programmer and GQ-5X SPI programmers. USB driver use Signed GQ USB 2.01 driver below. To get fully functional software, the software needs registration and activation code. Tested device data on GQ-5X NAND and GQ-5X SPI Programmer Old Revision Software.Missing.

• SCK option to support targets with low clock speed (. Note:- Make sure you burn the right fuse bit configration along with the firmware into atmega8 microcontroller for atemega8 the fuse bit are atmega8 HFUSE=0xC9 LFUSE=0xEF if you have a problem how to burn those fuse bit use the give serial avr programmer then please visit page for detailed information Step 5:- Driver installation on a PC:- At the first time when you connect your programmer to the pc your programmer will be dected as usbasp and you have to provide a proper path for drivers to be installed. This programmer use same driver as my privous use USB AVR prorammer Dected By the widnows Give the Instruction for a specfic location driver installation Give the path for driver to be installed USB AVR Programmer installed USB AVR programmer is being connected and shown in device manager On Linux and MacOS X no kernel driver is needed. Free Download Directsound Driver For Windows Xp more. Windows requires a driver for USBasp: (70 kB) Note: Windows Vista/7 x64 requires drivers with digital signature. Currently there are no official drivers for libusb (USBasp software is based on it) with such a signature.

Users reported that there is a tool named 'Driver Signature Enforcement Overrider' to avoid the signature check. Step 6:- Programming the other microcontrollers:- You can use Progisp software to burn the hex file in to the traget microcontrollers. Note: i don't suggest you to use any other sofware then the progisp.

But if this works with any other then you are free to use that. Step 4 says:- you have to first burn the firmware (that you have downloaded in setp 1) into the atmega8 mcu to act like a programmer.this firmware enables the programmer device to communicate with the computer usb port and the target chip you gonna program for your own use. Only after doing this you can program other mcu by this programmer.

The atmega8 as you purchased is not programmed any firmware. It's blank actually. So after step 4 only your programmer is ready to use now you can connect it to your 8051 mcu to program your firmware into the 8051 mcu if still have any question please feel free to ask. J1 is for switch target board power supply on and off which is delivered by the programmer j3 is for slowdown programming speed,, few chips doesn't support fast programming (chip enable program error occur) so set this jumper to slow down programming speed clock j2 is set when you want to upgrade firmware of the programmer x2 is nothing but a general purpose connector you can use any type of connector may be burg strip as i used and my be polarized header or idc 10 pin connector 3) no there is no need to do that but if you do it's good to reset the avr just pull it's reset pin down. Hi have to burn the firmware and fuse bits into programmer's atmega8 if not then first you have to do this with the help of some kind of programmer if you have access to some other programmer then it's fine use that for burning programmer's firmware, if not then you can make the serial port programmer then burn the firmware to the atmega8 first and then plug into the usbasp board why are you using ponyprog,does poneprog support usbasp? And it's usb programmer,it does not connect to COM port please use porogisp which is available for download from my blog led are not glowing means that you did' burn the programmer's fimware. 1) Can u help me out with that X2 connection, what exactly is it showing??